Meet the no planers and jointers

Multi-Jointer planer MH

meet the no planers and jointers

Designed to meet the evolving industry demands for increased production, higher No need to lock out the motors, as jointer is mounted outside the hood; no. Number of Knives. 3. Rabbeting Capacity motor easily handles the toughest jointing tasks. □ Heavy-duty . lets you adjust the feed rate to meet your needs. The unique multi-jointer/planer MH from Logosol. The jointer/planer MH is built the same way as No resetting between jointing, planing and moulding.

Benefits There is always a certain amount of slippage in Hydraulic Motors but when they are over sped the slippage increases dramatically Maintenance hours spent on the existing system Maintenance spent on existing Hydraulic drive for the feed table Roll wear from slippage Bushings and Bearings Gilbert Setworks Our engineering staff has developed what we believe to be the most user friendly, safe, and practical positioning system on the market.

Benefits Changes in Production: Possible in less than a few seconds Automatic Release: Quick release system and immediate return to production after wood jamming Skips: One button allows you to simultaneously move both side heads which keeps the same space between them Knives: Rapid automatic adjustment of cutterheads following sharpening of knives Precision: Constant precision of manufactured products only the first piece needs to be measured Gilbert Live Roll for Feed Table or Bridge Feed Rolls Diamond points bottom feed rolls, 10 in.

LG x 12 DIA.

meet the no planers and jointers

Grooved upper feed rolls, 10 in. LG x 12 in. First, you can't adjust the infeed table. You can only adjust the tilt of the outfeed table. But if things are not level left-right, good luck. About the only option is to shim it. Which is what I ended up doing to the infeed table as one side was about 0. Not much you say by itself, but after multiple passes, this gets pretty pronouced as it ends up making one twisted wood.

danunah.info: Customer reviews: Rikon Planer/Jointer, Inch

The bed is off. Per the manual, the only way to adjust it is to take it to a repair shop. One side was square the other was not. So, the planer is turning my boards into a trapezoid.

Because of the flimsy way the tables attach, they are not stiff enough, so the angles of the tables change when any weight is applied to their edges. I'd like to get rid of it by selling it, but I wouldn't feel right to do so, because I'd be passing on a pure nightmare to a fellow woodworker.

Do yourself a favor and don't buy this.

meet the no planers and jointers

If funds are an issue, you're much better off with quality hand planes. Unlike the other reviewers, I didn't have issues with the instructions.

  • Advantages
  • FELDER GROUP | Tel: +43 (0) 5223/58 500
  • Technical data

Immobilize the cutterhead by inserting tapered wood shims between the head and bearings, as shown below. Loosen the knife gib bolts just enough so that the knife moves with firm hand pressure. Raise the knife slightly higher than the top of the outfeed table. Now, lay the glass on the outfeed table, extended to fully contact the knife.

Press the glass to the table and slowly snug up the gib bolts, starting with ones at the ends and alternately working toward the middle.

Too much torque can force a knife out of alignment. To limit the amount of pressure you can apply, turn the wrench with only your thumb and forefinger.

Set each knife in turn, aligning it with the mark on the fence. Now, use the stick to check that each knife is set the same height as the others. Lay the stick on the outfeed table, lining up any one of the three table edge marks, and rotate each knife past it. All should move the stick the same distance at both ends.

For a high-tech way to set jointer knives, invest in a setting tool such as the Magna-Set.

Planer Upgrade Kits

It consists of two steel or plastic bars that slide along a pair of parallel rods. As shown below, each bar has small but powerful magnets that hold the jig to the table and the knives.

meet the no planers and jointers

This keeps each knife flush with the outfeed table while you tighten the gib bolts. A dial indicator setup, such as the A-Line-It, offers yet another way to set the knives.

Cantilevered Cutter Head Conversion

See the drawing below. The indicator tells you exactly how high the knives are from end to end, and in relation to each other.

These gauges work especially well with knives that you adjust with jack-screws that elevate the knives. Reinstall the cutterhead guard, and plug in the machine. If you can move it, you need to adjust the outfeed table to exactly the same height as the tops of the knives. Now, shut off the jointer, raise the outfeed table until it just contacts the workpiece, and lock it down.